|
||||
热电偶专用高温电缆High Temperature Cable Special For Thermocouple本产品为热电偶专用的高温连接线。产品具有优良的耐腐蚀性能,几乎不溶于任何 ,可耐油、耐酸碱等;具有优良的电绝缘性能,不吸潮,绝缘电阻大;具有阻燃性能。The cable is a special high temperature connecting wire of thermocouple. It has many good features such as excellent corrosion resistance, almost insoluble in any organic solvents, oil resistance, acid resistance, better electrical insulating properties, moisture resistance, big insulated resistance, flame resistance and so on. 一、产品执行标准 企标 Executive standard: enterprise standard二、型号ZR-KX-H-FFB高温补偿导线AGGYGG硅橡胶电缆[股份@有限公司]欢迎您其中变压电路其实就是一个铁芯变压器,需要介绍的只是后面三种单元电路。整流电路整流电路是利用半导体二极管的单向导电性能把交流电变成单向脉动直流电的电路。半波整流半波整流电路只需一个二极管,见图2。在交流电正半周时VD导通,负半周时VD截止,负载R上得到的是脉动的直流电全波整流全波整流要用两个二极管,而且要求变压器有带中心抽头的两个圈数相同的次级线圈,见图2。负载RL上得到的是脉动的全波整流电流,输出电压比半波整流电路高。 Type型号type 名称descriptionAKFFPXR200 K型热电偶专用高温屏蔽电缆High temperature shielding cable special for K type thermocoupleANFFPXR200 N型热电偶专用高温屏蔽电缆High temperature shielding cable special for N type thermocoupleAEFFPXR200 E型热电偶专用高温屏蔽电缆High temperature shielding cable special for E type thermocoupleAJFFPXR200 J型热电偶专用高温屏蔽电缆High temperature shielding cable special for J type thermocoupleATFFPXR200 T型热电偶专用高温屏蔽电缆High temperature shielding cable special for T type thermocouple三、使用特性 operating characteristics 1、工作温度:电缆导体长期工作温度为200℃。 Long term operating temperature of cable conductor is 200℃.ZR-KX-H-FFB高温补偿导线AGGYGG硅橡胶电缆[股份@有限公司]欢迎您注:触点一直保持动作。。线圈断电后才复位。。。记住。下图顺序:线圈,常闭触点,常触点顺序:线圈,常闭触点,常触点二次图详解先看红色线,这一部分从起动按钮"SB1"始,一直到零线是接通的,所以,当按下起动按钮时,KM1,KM3,KT均会接通。KM1辅助触点通过"自锁",使电路一直得电,处于接通状态。此时是星型启动。我们上面说了,通电延时型时间继电器,现KT线圈一直得电,待设定的时间到后,常常闭触点动作。 2、弯曲半径:电缆弯曲半径不低于电缆外径的10倍。Bending radius of cable shall be no less than 10 times that of cable outer diameter.& 05。 Flame resistant characteristic shall meet the requirements speculated in GB19666-2005 standard.四、性能参数表Performance parameter项目Item 单位Unit 技术指标Technical Indices绝缘电阻Insulated resistance MΩ 25电压试验Test voltage V 500V 1min 不击穿Finished cable shall endure 500v voltage test for 1 min without puncture.ZR-KX-H-FFB高温补偿导线AGGYGG硅橡胶电缆[股份@有限公司]欢迎您将程序下传到PLC中进行在线的调试。如果设备不动或运行中出现异常情况,先不要去修改程序,很可能是传感器没有调试到位,如果确保传感器无误,再去修改程序。调试完成后,再次编辑程序在上一步的调试中,由于对程序有所修改,故必须再次整体检查或编辑一下程序,然后将 终的程序下传到PLC中。保存程序在这一步中,要注意一个问题,就是应该将程序保存在什么地方?PC硬盘?闪存设备?硬盘?当然这些都不可以,所有这些存储设备都可能感染。 |
|